HomeAbout
ServicesAll servicesDry LiningPartitioningSteel Framing (SFS)ScreedingPlasteringSuspended CeilingsAcoustic SolutionsTape and JointingExternal RendersFire ProtectionHeritage & RefurbishmentsFacades
ProjectsSectorsHow we workAccreditationsGuidesWork with usContact
Linton House, London

Guide

Dry Lining or Wet Plaster: How to Choose

The choice between direct bond dry lining and wet plaster turns on the background, the specified build-up and how much drying the programme can absorb.

BS 8000-8 is the BSI code of practice for the design, installation and finishing of drylining systems, and BSI lists it as current. The Siniat Drywall Manual linings section (version 3.0.0, November 2024) describes direct bond dry lining as the simplest option for single layer lining of most masonry substrates.

The comparison below draws on manufacturer documents, so treat those statements as manufacturer claims.

Programme and drying

Wet plaster brings water into the building. The Thistle MultiFinish data sheet (PDS-110-04) says gypsum-based plasterwork must always be thoroughly dry before decorating. It gives no number of days.

The same sheet gives a specific warning on cement-based undercoats. They shrink on drying and can crack "up to days or even weeks after application". A finish applied before shrinkage is complete has an increased risk of delamination or cracking.

Siniat says its direct bond system "reduces drying out time speeding up internal fit-out". That is a vendor claim and the manual gives no figure.

Background and build-up

The two systems start from different backgrounds, and the limits are written into the documents:

  • Plaster: Thistle MultiFinish suits backgrounds from low suction, such as plasterboard or flat concrete treated with bonding agents, through to medium and high suction.
  • Direct bond: suitable for most level masonry. It is single layer boarding only, and stacking boards is prohibited.
  • Service space: Siniat says a service cavity of 10 to 25 mm can be created.
  • Use and location: Siniat lists new build residential and general renovation in normal humidity. External solid walls and basements are not suitable for bonding.
  • Moisture: Siniat directs substrates with uncontrolled moisture ingress to a different system, the Independent Wall Lining.

Preparation differs as well. For direct bond, Siniat says substrates must be clean and dust free with loose material removed, and treatment depends on suction:

  • Very low suction: may require mechanical fixing.
  • Low and medium suction: no treatment.
  • High suction: PVAC bonding agent.

Thistle says plaster on board is applied in two applications and trowelled to a smooth matt finish. It says gypsum undercoats are usually finished when set but not dry, because a dry undercoat has higher suction and may need damping down first.

If the specification calls for two layers of board for fire or acoustic reasons, direct bond is outside the manufacturer's stated use.

Where the standards sit

BS 8000-8 covers design, installation and finishing of dry lining. BSI listings show conflicting dates for it, so confirm the current edition date before citing it.

Sector differences between commercial and residential schemes come from the specification, fire strategy and acoustic requirements for each scheme. The right answer depends on the building rather than the sector.

Questions that settle most choices:

  • What is the background, and is it level and dry?
  • Is one layer of board enough for fire and acoustics?
  • Is a service cavity needed behind the board?
  • When can heating and ventilation run to dry the building?

A single layer direct bond lining on a level block wall in a dry new-build flat sits inside the manufacturer's stated use, while the same system on an external solid wall or in a basement sits outside it.

Common questions

Can permeable paint go on new plaster before it is dry?

The Thistle data sheet says a coat of permeable paint can be applied in the interim, although the plasterwork must always be thoroughly dry before decorating.

Can boards be stacked in a direct bond lining?

Siniat's manual says no. The system is only suitable for single height boarding, and boards are to be 5 mm less than floor to ceiling height.

Do plaster data sheets give drying days?

The Thistle MultiFinish sheet read for this guide does not. Check the data sheet for the product specified, because backgrounds and thicknesses differ.